XCMG Chusheng teaches you the easiest way to identify the quality of sprinklers. Sprinklers are also known as spray trucks, multi-function sprinklers, landscaping sprinklers, water tankers, and water trucks. Sprinklers are suitable for all kinds of road flushing, trees, green belts, lawn greening, construction of roads, factories and mines, and high-rise building flushing. With sprinkler, dust, high and low spray, pesticide spraying, guardrail flushing and other functions, used in urban roads, large factory areas, troops, gardens and other units to clean the road, health, dust, water, spray pesticides, etc., in order to achieve landscaping Environmental role.
Four points to identify the quality of the sprinkler:
1. See if the protective surface is intact. Most sprinkler parts are coated with a protective layer at the factory. For example, the piston pin and the bearing bush are protected by paraffin; the surface of the piston ring and the cylinder liner are coated with anti-rust oil and wrapped in wrapping paper; valves, pistons, and other impregnated anti-rust oils are sealed in plastic bags. If damage to the sealing sleeve, loss of wrapping paper, loss of rust-proof oil or paraffin is found during purchase, it shall be returned.
2. See if the surface of the sprinkler fitting is rusted. Qualified parts surface, both a certain degree of precision and bright finish, the more important parts, the higher the precision, the more stringent rust-proof and anti-corrosion packaging. Should pay attention to inspection when purchasing, if found parts of rusty spots, mold spots or rubber pieces cracking, loss of elasticity, or the surface of the journal has a clear turning pattern, should be exchanged.
3. Look at the geometry for deformation. Some sprinkler parts are easily deformed due to improper manufacture, transportation, and storage. During the inspection, the shaft part can be rolled along the glass plate to see if there is any light leakage between the part and the glass plate to judge whether it is bent; when the clutch plate or friction plate is selected, the steel plate and friction can be selected. Observe whether the film is warped in front of the film; when selecting the oil seal, the end surface of the oil seal with the frame should be perfectly round, and it can be attached to the flat glass without bending; the outer edge of the frame oil seal should be straight, and it should be deformed by hand After loosening, you should be able to return to your original condition. In the purchase of various kinds of pads, you should also pay attention to check the geometry and shape.
4. See if the junction is flat. Sprinkler parts in the process of handling, storage, due to vibration, bumps, often in the joints produce burrs, indentation, damage or cracks, affecting the use of parts. Please pay attention to inspection when purchasing. Hubei Cheng Li sprinkler trucks use high-quality dedicated sprinkler pumps. Special functions are: after the punch (spray), sprinkle, with side spray (shower) with the back of the work platform, install green sprinkler on the platform gun (gun with heavy rain, moderate rain, drizzle, fog can be adjusted) with suction pipe, With fire joints, with self-flow valve, self-priming self-discharge, optional 20 meters green spray reel, high-altitude operations, with the crane hanging cargo and other functions. Function realization principle: The engine is mainly used to initiate the gearbox. The power take-off device installed on the gearbox initiates the sprinkling of the water pump. The water sprinkling pump attacks the power and sprays the liquid outside the tank through the pipe network.
Xigong Chusheng (Hubei) Special Purpose Vehicle Manufacturing Co., Ltd. Production and sales: sprinkler series, sewage suction truck series, suction truck series, garbage truck series, sweeping vehicle series, tanker truck, oil truck series, aerial working truck series , Dump Truck Series, Coach Vehicle Series, Semitrailer Series, Fire Truck Series, Chemical Vehicle Series, Powder Material Vehicle Series, Concrete Mixer Series, Wrecker Series, Pressure Vessel Series, etc. More than 300 series of more than 10 series Models, after-sales service in place. National home delivery, welcome to inquire negotiate. Company website: http://, contact phone number!
What is the X Banner Stand? X exhibition stand is an exhibition display item with an X banner stand on the back used for advertising purposes. What are the advantages of the X stand? The advantages of X banner stand can be summarized as concise design, convenient transportation, easy storage, simple installation, and economic practicality. It is a lightweight and fast advertising and promotional tool. The X banner is a type of advertising and promotional material for public places, events, gatherings, or business stores, as well as a display for wedding celebrations. It is small, exquisite, convenient to carry, detachable, interchangeable, and can be used repeatedly for a long time. The X banner stand adopts advertising equipment spray painting machines for spray printing production. The overall components do not need to be assembled, and are equipped with adjustable angle brackets, which are flexible and versatile, small in size, and diverse in styles.
Light Weight X Banner,Lightweight X Banner,Trade Show Exhibition X Banner,Flex X Banner Stand
SUZHOU JH DISPLAY&EXHIBITION EQUIPMENT CO.,LTD , https://www.jh-posterstand.com