The car can gallop on the road, relying on the precise cooperation of the various components, less one link, will have a lot of adverse effects on the normal driving of the vehicle. The throttle is in the engine, in a position similar to the gate, and it is naturally very important. So what is the role of the throttle? Why do you clean the throttle regularly?
On gasoline engines, the throttle is generally installed in the intake of the engine. Above it is the car's air filter, connected to the engine body below. Therefore, the throttle is again compared to the image of the throat of the engine.
The throttle is a valve that can be adjusted to open and close. Just as the faucet can regulate the flow of water, the throttle can also adjust the amount of air entering the engine. The air enters the combustion chamber inside the engine through the throttle valve, and is mixed with the fuel ejected from the electronic nozzle to form a flammable gas. The flammable gas burns inside the engine to work, driving the car.
If there is more flammable mixture, the faster the engine will spin. If there is less flammable mixture, the engine will spin more slowly. Therefore, the throttle can control the speed of the engine, which coincides with the role of the other part of the car, the "throttle pedal." It turns out that the accelerator pedal of the car is connected to the throttle through a certain mechanical structure. When the throttle is depressed, the throttle will open. When the throttle is stepped on, the opening of the throttle will be larger. The faster you accelerate.
The previous throttle was that the cable was directly controlled by the accelerator pedal, but now the technology is more developed, and the electronic control is controlled by the computer and is safer. The key to the throttle is to control the airflow and the normal operation of the engine.
And some factors can cause the throttle to become unregulated, and the dirt is. Because the throttle valve controls the flow rate of the intake air, the air enters the engine from the throttle valve, and dust is inevitably dropped. Therefore, it is necessary to periodically clean and clean the wash or replace the hole filter. When the normal throttle is closed, it will be closed. Then, when the time is long, there will be dirt, which will cause the throttle opening to become larger. The air flow will also become larger. Not only will it not save energy, but it will also save fuel. Powerless, can't give oil.
Cleaning should also pay attention to the use of special cleaning agents, but also to avoid the throttle electronic control components is the throttle motor, when cleaning, avoid avoiding as much as possible. When cleaning the throttle valve, it will be used to clean the throttle flap, which will change the original position. It needs to be matched. It is necessary to pay attention to the use of the computer to match the original opening after cleaning. Otherwise, the computer will default now. This is the original opening, resulting in a large intake air flow and unstable idle speed. So don't let your own words move.
Comparing the throttle to the throat of the engine is very appropriate, which can more vividly explain the key role of the throttle. If the throttle is dirty, it will adversely affect the performance of the engine. Therefore, the cleaning of the throttle should also be taken seriously.
At present, the die casting industry mainly die casts aluminum alloy, zinc alloy and magnesium alloy, as well as a small amount of copper alloy and other metal die casting parts. Since die-casting uses molds to form, a relatively long mold manufacturing cycle is required in the early stage, and the production efficiency is high after the mold is manufactured. Therefore, for die casting products, it is especially suitable for mass production, with relatively low cost and high efficiency. However, since the die-casting material is a metal material, it is more difficult to demould compared with the plastic material, so a relatively large demolding slope needs to be used, and the shrinkage of the metal itself causes the precision not to be very high. For positions that require precision assembly, subsequent secondary CNC machining is usually required to achieve the accuracy requirements. Die casting parts can be seen everywhere in industries such as automobiles, lighting, machinery, communications, electronics, and home appliances. Some die-casting products as shown below:
Die Casting Products,Die Cating Part,General Die Casging,Zinc Alloy Die Casting Parts,Zinc Alloy Die Casting,Metal Die Casting Products
Shenzhen SCZY Technology Co.,Ltd , https://www.szcasting.com