When it comes to small tankers, everyone first thinks about whether it is related to its safety issues. Because tankers cannot tolerate potential safety hazards, we must strictly follow the principle of small tank trucks in our work on weekdays. Safe operating procedures to carry out. Small tanker before use, in use, after use have strict regulations, the following to each introduce them separately, hoping to have some help for everyone:
1. Preparation before use (1) Insert the conductive rod into the ground to make it “groundedâ€. If the ground is dry, it can be boiled to make it wet, and the grounding is ensured. Check the ground chain to make contact with the ground.
(2) Open the tanker control box door and check the valve handles to make contact with the ground.
(3) When the oil pump is used for the first time, if there is no oil in the pump, it should be refueled in advance, and 10 liters of oil can be added through the oil inlet.
(4) Check the lubricant oil level in the gearbox to the lower edge of the oil surface screw hole. If insufficient, add gear oil.
(5) Check the transmission control lever to make it in neutral position, check the position of the power take-off handle, make it horizontal to right, make it horizontal to right position, check the throttle controller to make it minimum.
2. Operation of oil pump and power take-off device (1) Start the relevant pipe and start the engine. When the original car pressure gauge reaches 0.3Mpa, step on the clutch pedal, open the power take-off box operation switch, and slowly loosen the clutch (too fast Damage to the power take-off and gearbox will be caused.
Through the throttle controller, the working speed of the oil pump can be controlled.
(2) Stop propelling the throttle controller and adjust it to the minimum. Step on the clutch pedal and pull the power take-off control switch back to the original position to make the power take off box.
3. Check after use (1) Check whether the power take-off control switch is returned, check whether the throttle controller is at the minimum position.
(2) check the valve handle position, are closed.
(3) Close the control box door.
After reading the above introduction, I hope that everyone can strictly follow the above rules in the process of use. Our company staff sincerely welcome new and old customers from all walks of life to come to study guidance, let us work together to create a better tomorrow!
1. Preparation before use (1) Insert the conductive rod into the ground to make it “groundedâ€. If the ground is dry, it can be boiled to make it wet, and the grounding is ensured. Check the ground chain to make contact with the ground.
(2) Open the tanker control box door and check the valve handles to make contact with the ground.
(3) When the oil pump is used for the first time, if there is no oil in the pump, it should be refueled in advance, and 10 liters of oil can be added through the oil inlet.
(4) Check the lubricant oil level in the gearbox to the lower edge of the oil surface screw hole. If insufficient, add gear oil.
(5) Check the transmission control lever to make it in neutral position, check the position of the power take-off handle, make it horizontal to right, make it horizontal to right position, check the throttle controller to make it minimum.
2. Operation of oil pump and power take-off device (1) Start the relevant pipe and start the engine. When the original car pressure gauge reaches 0.3Mpa, step on the clutch pedal, open the power take-off box operation switch, and slowly loosen the clutch (too fast Damage to the power take-off and gearbox will be caused.
Through the throttle controller, the working speed of the oil pump can be controlled.
(2) Stop propelling the throttle controller and adjust it to the minimum. Step on the clutch pedal and pull the power take-off control switch back to the original position to make the power take off box.
3. Check after use (1) Check whether the power take-off control switch is returned, check whether the throttle controller is at the minimum position.
(2) check the valve handle position, are closed.
(3) Close the control box door.
After reading the above introduction, I hope that everyone can strictly follow the above rules in the process of use. Our company staff sincerely welcome new and old customers from all walks of life to come to study guidance, let us work together to create a better tomorrow!
Shijiazhuang Shangzu Building Materials Technology Co.,Ltd. , https://www.shangzuchem.com