1. The operator should be familiar with the performance structure of the machine tool and follow the safety rules.
2. Before the vehicle is driven, fuel should be provided according to the regulations to ensure that all parts are well lubricated.
3. Check whether the bolts of each department are tight, whether the transmission mechanism and the cutter device are normal, and whether the protection facilities and electrical system are good.
4. Run the empty car for 2 to 3 minutes before confirming normal operation before working.
5. The length of the processing material of the flat planer shall not be less than 700mm, and the thickness shall not be less than 10mm; the length of the processing wood of the planer shall not be less than the center distance of the pick-up drum, and the thickness shall not exceed the upper and lower limits of the table lifting.
6. The sloping material must not have nails, cement, gravel, iron filings and other objects. The flat planer shall push the material into the flat, and shall not be skewed and planed. It shall not be pushed backwards; the wood processed on the planer shall have a flat base surface, and the amount of knife shall not exceed 2~3mm.
7. When the plane planer is operated, the hand should be supported on the top of the wood to move smoothly and evenly. When shaving the sheet, the grab must be used. The distance between the fingers and the table must not be less than 150mm.
8. It is forbidden to use a blunt knife and planer. The planer is rubbed with oilstone once every 3 to 4 hours. When grinding with a grinding wheel, the feeding amount should not be too large, so that the edge will not be blue and the hardness will be reduced.
9. Turn off the power when installing the blade. After the blade is installed, tighten the fastening bolts and open the empty car to check if the planer is in balance. If it is considered correct, stop it before proceeding.
10. During the planing process, always check the safety of the guard and the fixing screws. Remove chips in time to avoid clogging. Clearing chips must be done after parking
11. During the work, the machine table is not allowed to place tools, sundries or on behalf of the processing of wood, and it is forbidden to hit the table with tools.
12. After the work is completed, cut off the power supply, clean the machine tool and work site, and place the finished products and semi-finished products at the designated locations.
2. Before the vehicle is driven, fuel should be provided according to the regulations to ensure that all parts are well lubricated.
3. Check whether the bolts of each department are tight, whether the transmission mechanism and the cutter device are normal, and whether the protection facilities and electrical system are good.
4. Run the empty car for 2 to 3 minutes before confirming normal operation before working.
5. The length of the processing material of the flat planer shall not be less than 700mm, and the thickness shall not be less than 10mm; the length of the processing wood of the planer shall not be less than the center distance of the pick-up drum, and the thickness shall not exceed the upper and lower limits of the table lifting.
6. The sloping material must not have nails, cement, gravel, iron filings and other objects. The flat planer shall push the material into the flat, and shall not be skewed and planed. It shall not be pushed backwards; the wood processed on the planer shall have a flat base surface, and the amount of knife shall not exceed 2~3mm.
7. When the plane planer is operated, the hand should be supported on the top of the wood to move smoothly and evenly. When shaving the sheet, the grab must be used. The distance between the fingers and the table must not be less than 150mm.
8. It is forbidden to use a blunt knife and planer. The planer is rubbed with oilstone once every 3 to 4 hours. When grinding with a grinding wheel, the feeding amount should not be too large, so that the edge will not be blue and the hardness will be reduced.
9. Turn off the power when installing the blade. After the blade is installed, tighten the fastening bolts and open the empty car to check if the planer is in balance. If it is considered correct, stop it before proceeding.
10. During the planing process, always check the safety of the guard and the fixing screws. Remove chips in time to avoid clogging. Clearing chips must be done after parking
11. During the work, the machine table is not allowed to place tools, sundries or on behalf of the processing of wood, and it is forbidden to hit the table with tools.
12. After the work is completed, cut off the power supply, clean the machine tool and work site, and place the finished products and semi-finished products at the designated locations.
Tv Backplane Mould Chart,Tv Backplane Mould Kit,Tv Backplane Mould Steel,Server Chassis Mould Method
Kunshan Wangdaxin Precision Mould Co., Ltd. , https://www.wdxmould.com