1, choose the product brand
When choosing petrol sightseeing cars, everyone should have a good understanding of the industry of gasoline sightseeing car brands and see if their companies have special equipment production licenses from the national technology-related departments. Now there are many small-scale production workshops in the market, privately applied and modified some of the brand's qualifications, to sell at low prices, disrupting the operation of the formal market. The purchase of petrol sightseeing cars modified by small workshops is a great safety risk. Once accidents are caused in the process of use, there is no guarantee and more losses will be caused. The selection of manufacturers with qualified production does not mean that there are few problems with the safety of the product itself. In the course of using the product, failures can also be provided with good after-sales services and protection.
2, vehicle product structure
The tourist vehicles that we usually ride are open design, but the higher the occupants are from the ground, the greater the danger. Nowadays, some tourist vehicles sold on the market are converted using light vehicles and mini-car chassis, while the occupants are more than 70 cm above the ground. However, the height between the vehicle and the floor that has undergone an overall renovation of the gasoline sightseeing vehicle is less than 50 cm, which is a relatively large degree of improvement in safety.
3, the reliability of vehicle braking
The reliability of vehicle brakes for sightseeing vehicles is mainly expressed in front and rear drums and four-wheel drum brakes, but most of them recommend that you select the front and rear drum brake modes. At the same time, the most important point is that there is no vacuum booster. This is a major guarantee that braking can be timely, effective, and more comfortable.
4, product safety
At present, there are some sightseeing and sightseeing vehicles on the market that do not control the speed of the vehicle. Some vehicles can continue to accelerate at speeds above 50 KM/H. Some vehicles that use fuel power, such as petrol sightseeing vehicles, can reach and exceed the maximum speed of 60 km/h. . However, for these open-air sightseeing vehicles with higher speeds, the safety of passengers is greatly affected. There are many products that can only control the speed limit by controlling the throttle, and some will control the overall speed through the computer, which will be more safe and reliable. (Text / Sun Ni)
Open rubber and plastic mixing is the rubber factory used to prepare plastic rubber, rubber or hot refining, a type of roller exposed rubber refining machinery. This machine is suitable for EVA,rubber,synthetic rubber,hot melt and all kinds of chemistry raw material to mix ,mediate and disperse, and then put into the mass production. It is the best choice to test, make sample and learning in school.
16inch automatic crusher mill
Advantage
1. The roller is made of chilled casting vanadium & titanium alloy iron which is hard and wear-resisting, the surface hardness is above 70degree, the surface coating is about 15mm.
2. Hard tooth gear reducer with well-design structure, low noise, high efficiency and long service life.
3. Self-aligning bearing is well matching with the bearing inside leakage-proof device. The sealers are made of high temperature,wear, oil resistance material,which have very good sealing effect.
4. All main electrics are imported, the alternating current contactor is Shilin brand. The switch and button are Taiwan Tend brand.
5. Circulating lubrication system solves the oil leakage problem. The feature of this system is easy to maintain,easy to replace.
6. This machine is installed with overload protection device which protect the machine will not broken if the machine is overload. The machine will reverse 1/3 round when press the emergency stop button,which sure the production safety.
7. The [U" shape frame is whole set casting, but other factory welded together.
8. The machine base is welded by national standard I steel.
Main parameter
|
Name |
A Automatic crusher mill |
|
Front roller diameter (mm)(Smooth roller) |
400 |
|
Rear roler diameter (mm)(Groove roller) |
450 |
|
Roller length(mm) |
840 |
|
Front roller speed (m/min) |
12.67 |
|
Speed ratio |
1:1.63 |
|
Max roller gap(mm) |
10 |
|
Nip adjustment |
Manual |
|
Mixing capacity(kg) |
20 |
|
Power (kw) |
45-8 |
|
Motor RPM(r/min) |
740 |
|
Reducer ratio |
45 |
|
Reducer model |
315 |
|
Roller bearing diameter(mm) |
260 |
|
Bearing mode |
352952YA |
|
Bearing size(mm) |
360×260×150 |
|
Name |
B mixing mill |
|
(mm) Front roller diameter(smooth roller) |
400 |
|
Rear roller diameter (mm)(smooth roller) |
400 |
|
Roller length(mm) |
840 |
|
Front roller working speed (m/min) |
19.36 |
|
Speed ratio |
1:1.5 |
|
Max roller gap(mm) |
10 |
|
Nip adjustment |
Manual |
|
Mixing capacity(kg) |
20 |
|
Power (kw) |
37KW |
|
Motor RPM(r/min) |
980 |
|
Reducer ratio |
45 |
|
Reducer model |
315 |
|
Roller bearing diameter(mm) |
260 |
|
Bearing model |
352952YA |
|
Bearing size(mm) |
360×260×150 |
Mixing Mill Manchine,Open Mill,Rubber Mixing Mill,Roller Mill
SHIJIAZHUANG LONGXUAN TRADING CO., LTD , https://www.longxuanmachine.com