In the application of air compressors, the issue of air compressor exhaust has always been a major issue for the majority of users, so how to effectively improve the air compressor displacement? Shanghai has 20 years of experience in air compressor technology Dechener Compression Machinery Co., Ltd. Chen Gong told us that there are many factors that affect the air compressor displacement, which can be roughly divided into four major aspects: speed, leakage, cooling effect,
In the application of air compressors, the issue of air compressor exhaust has always been a major issue for the majority of users, so how to effectively improve the air compressor displacement? Shanghai has 20 years of experience in air compressor technology Dechener Compression Machinery Co., Ltd. Chen Gong told us that there are many factors that affect the air compressor displacement, roughly divided into four major areas: speed, leakage, cooling effect, inhalation status, as detailed below:
Speed ​​- Air compressor displacement is proportional to speed. The speed will often change with the voltage and frequency of the grid. When the voltage is reduced (for asynchronous motors) or the frequency is reduced, the speed will drop, reducing the compressor displacement.
Leakage - Air compressor rotor and rotor and between the rotor and the shell are not in contact with the operation, there will be a certain gap, it will have a gas leak. When the pressure-increased gas leaks through the gap to the suction duct and the suction groove that is inhaling, the exhaust volume of the compressor will be reduced. In order to reduce the amount of leakage, seal teeth are formed on the tops of the driven rotors, seal grooves are formed on the tooth roots of the active rotors, and annular or strip-shaped seal teeth are also machined on the end surfaces. If these seal lines are worn, the leakage will increase and the air compressor will reduce its displacement.
Cooling effect - the temperature of the gas will increase during the compression process, the temperature of the air compressor rotor and the casing will increase accordingly, so in the process of inhalation, the gas will be heated by the rotor and the casing to expand, so accordingly Will reduce the amount of inspiration. Some of the air compressor rotors use oil cooling, and the casing is cooled by water. One of its purposes is to reduce its temperature. When the cooling effect is not good, the temperature will increase, and the air compressor discharge will be reduced;
Suction state - the general volume type air compressor, inhale the same volume. When the suction temperature increases, or the suction pipe resistance is too large and the suction pressure decreases, the density of the gas decreases, and the mass discharge of the gas will accordingly be reduced.
Then learned that the four major factors affect the air compressor displacement, and effective to improve the air compressor displacement is not difficult to do, Chen Gong told us to increase the air compressor displacement is to increase the output coefficient In this regard, he also gave us detailed instructions:
1. It is necessary to properly increase the speed of the air compressor;
2. Always maintain the tightness of the output air compression system piping, intake valves, gas tanks, and coolers;
3. We must correctly choose the size of the clearance volume;
4, to maintain the air compressor suction valve and exhaust valve sensitivity;
5, to maintain the tightness of the air compressor valve and packing;
6, reduce the gas suction air compressor resistance;
7, to maintain the tightness of the compressor piston ring;
8. When the compressor is in operation, ensure that it is inhaled with relatively dry and cold gas;
9. If necessary, clean the air compressor cylinders and other parts.
10. Advanced cooling systems are recommended when conditions permit;
Filter Press
1. Using advanced technology, the appearance is beautiful and elegant.
2. High structural rigidity, smooth operation and low noise.
3. Equipped with advanced concentration pretreatment equipment (good for sludge flocculation) and low operating cost.
4. The gravity dewatering area is equipped with advanced distributors to distribute materials evenly and extend the life of the filter belt.
5. It has an extra-long gravity dewatering zone and a wedge-shaped dewatering zone, which fully dehydrates the material and ensures that the material will not overflow in the pressing zone.
6. The roller system is arranged scientifically and orderly. Gravity dehydration, wedge dehydration and press dehydration are discharged separately without interfering with each other. The diameter ratio of the press dehydration roller is large and the dehydration effect is good. Therefore, it has large production capacity, energy saving and high efficiency.
7. The continuous operation from feeding to mud cake discharge has a high degree of automation. A PLC interface can be set up as needed to facilitate centralized microcomputer control.
8. The power transmission mechanism adopts mechanical or variable frequency stepless speed regulation, with a large speed regulation range and wide adaptability.
9. The filter belt is equipped with a reliable backwash device to ensure the dehydration effect of the filter belt.
10. Use pneumatic tensioning and pneumatic automatic deviation correction devices to ensure the safe and normal operation of the filter belt.
11. The operation is safe and reliable, using infrared safety protection and a full range of emergency safety parking devices.
12. Filter belts with different structures can be configured according to different materials to achieve high filtration accuracy.
Filter Press,Pp Plate Filter Press,Syrup Filter Press,Belt Filter Press
Changzhou Senjie Environmental Protection Equipment Co., Ltd. , https://www.jssenjie.com