40000mAh Lithium Jump Starter for Car, SUV Truck, and Tank

1. 12V 2000A Peak Current CARKU Jump Starter for Tanks

2000Amp peak current and 1000A start current lithium jump starter EPower-99A is extremely  powerful to start all vehicles 12V or 24V, even tank. Handheld jump starter is easy to take it out from your vehicle when you need it.  It is much less lighter and longer life cycles than the lead acid battery jump starter. Nowadays, lead acid battery heavy duty jump starter is gradually replaced by lithium battery jump starter in the automotive industry.  If you are running car repair store or sell professional automotive tool, why not try it?



 

CHARGING XX%

Shows up the percentage of being charged when it is connected to 230V power supply 

BATTERY XX%

Shows up the amount of internal battery capacity. At least 60% are recommended to jump start a car.

LOW BATTERY RECHARGE NOW

Indicates low battery, please recharge.

USB1 USB2 ON

USB port 1 and 2 are available to recharge mobiel USB devices

WARNINGCLAMPS REVERSED

Shows that the clamps are connected reversely. At this time the start is prevented. Please remove the clamps and connect them in the right way. The red clamp must be connected to the positive (+) terminal and the black clamp to the negative (-) terminal of the battery. If you are sure that the connections are correct but this warning still shows up, press the Power button for three seconds to ignore this warning.

SHORT CIRCUIT CHECK ALL CONNECTIONS

It indicates a short circuit. At this time the start is prevented. Please remove the clamps and press the power button for three seconds before reconnecting the clamps to the battery.

12V JUMP START READY

Shows up when heavy duty jump starter EPower-99A is connected to a 12V battery and is ready to jump start. If EPower-99A cannot detect the battery or the battery is too low to be detected, you may use the "Expert Mode" for manually choosing your 12V battery type and jump start your 12V car battery.

24V JUMP START READY

Shows up when EPower-99A is connected to a 24V battery and is ready to jump start. If EPower-99A cannot detect the battery or the battery is too low to be detected, you may use the "Expert Mode" for manually choosing your 24V battery type and jump start your 24V car battery.

LED Flashlight:

the lumen of led light is 3W, and there are three modes: lighting, strobe, and flashing. Please press the button on the front till 3 or 5 second to see the lighting. If you want to change the any of these mode,you can press it at one time.

 

 

2 .Accessories:

 

* 3 in 1 USB cables

* Home Charger

* Smart jumper cable

* Manual

 

3. How to jumpstart lithium battery starter charger EPower-99A?

1.Make sure the battery is not less than 60% shown on the LCD display.
2.Connect the RED clamp to the vehicle's battery positive (+) terminal and connect the BALCK clamp to the vehicle's battery negative (-) terminal.

3.When you use EPower-60 jump start 12V car,it diaplays"12V JUMP START READY",when you use EPower-60 jump start 24V car,it diaplays"24V JUMP START READY".
4.Start the vehicle.

5.When the vehicle is restarted, please remove the jumper cable from Jump Starter and remove RED and BALCK clamps from the vehicle battery.

 

4. What vehicles can you start?

Auto battery engine booster 40000mAh EPower-99A can start up to all petrol cars, SUV, Mower, motocycles, or all diesel trucks, even tanks.

5. Related Product:

1200A 12V Truck Battery Booster 30000mAh
1000Amp 24000mAh Heavy Duty Car Jump Starter
Gas & Diesel Mini Jump Starter 18000mAh

1. 12V 2000A Peak Current CARKU Jump Starter for Tanks

2000Amp peak current and 1000A start current lithium jump starter EPower-99A is extremely  powerful to start all vehicles 12V or 24V, even tank. Handheld jump starter is easy to take it out from your vehicle when you need it.  It is much less lighter and longer life cycles than the lead acid battery jump starter. Nowadays, lead acid battery heavy duty jump starter is gradually replaced by lithium battery jump starter in the automotive industry.  If you are running car repair store or sell professional automotive tool, why not try it?



 

CHARGING XX%

Shows up the percentage of being charged when it is connected to 230V power supply 

BATTERY XX%

Shows up the amount of internal battery capacity. At least 60% are recommended to jump start a car.

LOW BATTERY RECHARGE NOW

Indicates low battery, please recharge.

USB1 USB2 ON

USB port 1 and 2 are available to recharge mobiel USB devices

WARNINGCLAMPS REVERSED

Shows that the clamps are connected reversely. At this time the start is prevented. Please remove the clamps and connect them in the right way. The red clamp must be connected to the positive (+) terminal and the black clamp to the negative (-) terminal of the battery. If you are sure that the connections are correct but this warning still shows up, press the Power button for three seconds to ignore this warning.

SHORT CIRCUIT CHECK ALL CONNECTIONS

It indicates a short circuit. At this time the start is prevented. Please remove the clamps and press the power button for three seconds before reconnecting the clamps to the battery.

12V JUMP START READY

Shows up when heavy duty jump starter EPower-99A is connected to a 12V battery and is ready to jump start. If EPower-99A cannot detect the battery or the battery is too low to be detected, you may use the "Expert Mode" for manually choosing your 12V battery type and jump start your 12V car battery.

24V JUMP START READY

Shows up when EPower-99A is connected to a 24V battery and is ready to jump start. If EPower-99A cannot detect the battery or the battery is too low to be detected, you may use the "Expert Mode" for manually choosing your 24V battery type and jump start your 24V car battery.

LED Flashlight:

the lumen of led light is 3W, and there are three modes: lighting, strobe, and flashing. Please press the button on the front till 3 or 5 second to see the lighting. If you want to change the any of these mode,you can press it at one time.

 

 

2 .Accessories:

 

* 3 in 1 USB cables

* Home Charger

* Smart jumper cable

* Manual

 

3. How to jumpstart lithium battery starter charger EPower-99A?

1.Make sure the battery is not less than 60% shown on the LCD display.
2.Connect the RED clamp to the vehicle's battery positive (+) terminal and connect the BALCK clamp to the vehicle's battery negative (-) terminal.

3.When you use EPower-60 jump start 12V car,it diaplays"12V JUMP START READY",when you use EPower-60 jump start 24V car,it diaplays"24V JUMP START READY".
4.Start the vehicle.

5.When the vehicle is restarted, please remove the jumper cable from Jump Starter and remove RED and BALCK clamps from the vehicle battery.

 

4. What vehicles can you start?

Auto battery engine booster 40000mAh EPower-99A can start up to all petrol cars, SUV, Mower, motocycles, or all diesel trucks, even tanks.

5. Related Product:

1200A 12V Truck Battery Booster 30000mAh
1000Amp 24000mAh Heavy Duty Car Jump Starter
Gas & Diesel Mini Jump Starter 18000mAh

Petrochemical pumps refer to pumps used in petrochemical industry. Because almost all the transporting liquid is flammable, and most of the temperature and pressure conditions are harsh, higher or highest level pumps are required.
Requirements for petrochemical pumps in petrochemical plants
a. For petrochemical pumps that transport flammable, explosive, toxic or precious media, shaft seals must be reliable or non-leak pumps such as canned motor pumps, magnetic drive pumps, pneumatic diaphragm pumps, etc.
b. For petrochemical pumps that transport corrosive media, it is required to use corrosion-resistant materials for the flow parts.
c. For petrochemical pumps transporting solid particulate media, it is required that the flow-through parts be made of wear-resistant materials, and if necessary, the shaft seals should be washed with clean liquid.
Must meet site installation requirements
a. For petrochemical pumps installed in the presence of corrosive gases, measures to prevent atmospheric corrosion are required.
b. For petrochemical pumps installed at an outdoor ambient temperature below 20 ° C, it is required to consider the cold brittleness of the pump and use low temperature resistant materials.
c. For petrochemical pumps installed in explosion areas, explosion-proof motors shall be used according to the explosion area grade.
d. For factories that require major maintenance once a year, the continuous operating cycle of the pump should generally not be less than 8000h. In order to meet the requirements of a three-year overhaul, API 610 (10th edition) stipulates that the continuous operation cycle of pumps for the petroleum, petrochemical and natural gas industries is at least 3 years.
e. The design life of petrochemical pumps is generally at least 10 years. API 610 (10th edition) stipulates that the design life of centrifugal pumps for the petroleum, petrochemical and natural gas industries is at least 20 years.
f. The design, manufacture and inspection of petrochemical pumps shall comply with the relevant standards and specifications.
g. The pump factory should guarantee the performance of the pump within the range of the power supply voltage and frequency. China's power supply voltage and frequency change range is: voltage 380V ± 10%, 6000V ± 10%; frequency 50Hz ± 1Hz.

For Petrochemical Industry Chemical Pumps

Chemical Process Pump,For Petrochemical Industry Chemical Pumps,Horizontal Waste Water Pump,Vertical Centrifugal Pump

Sichuan Zigong Industrial Pump Co.,Ltd. , https://www.zgpump-global.com