Plastic Material and Waterproof Speaker Horn

Product show:


Technical parameter:


Features:
1.The real test in our laboraroy that show to us the horn can get 110db at least.
2.Super long surround sound,it make the sound powerful and comfortable so that decrease the trafficaccident.
3.We used the imported high quality manganese steel to make the soundboad so that can make the fullest possible "BABA~~" sound.
4.We use the most advanced Teflon coat technology.I can be dust-proof and water-proof effectively(We must inform you that there are not have any horn factory can make a universal horn that all waterproof).It prolong the lifetime of the horn effectively.
5.We used the 100%ABS material to make the horn bulb.It has very good Heat resistance,impact resistance,anti-corrosion so that can prevent the dinas and the heat of the engine damage for the horn.Anyway,it also has high hardness characteristic.It can drop from 1 meter that is not easy to break.

What should I note when I am Installing and using?
a. Snail down or 45 degree Angle installation, Prevent water  into coiled directly
b. If you are not special peason , dont change the angle degree of Steel Support,or it will change the Original air gap
c. mounting torque of Steel support is between 6Nm to 11Nm.
d. The horn support should be mounted to Solid surface to avoid resonance.
e. In order to avoid contact with other parts of the car,The horn should be connected with horn support and installed to wide and Ventilated place.
f. Nonpolarity requirements for this product, the connected place of the wire should solid enough, Double horn should installed on solid part of car body in parallel way.
g. Keep away from car motor and much Radiation place. Not be too low mounting.
h. Don't keep the horn on for 60 seconds, or it will lead to the coil burned down.
i. Using copper wire, more than 1.5mm for wire Diameter, the wire length should less than 4m.
j. Standard mounting Voltage, input working current more than 30A,12V horn voltage: 9-14.5V  


Our company is a professional manufacturer and exporter that is concerned with the design , development and production of auto parts , we are
fully committed to producing technologically advanced auto parts.





Factory show:

Certifications:


Exhibition:


Contact us:
Guangzhou Jindong Electronic Technology Co.,LTD 
Add: No.1,Gudong Industrial Zone,Gulong Road,ShawanTownship,Panyu District,Guangzhou

Summer wei
 
Tel:+86-020-34738085                                  
Mob:+86-13928710276
Fax:+86-020-84737552
  Product show:


Technical parameter:


Features:
1.The real test in our laboraroy that show to us the horn can get 110db at least.
2.Super long surround sound,it make the sound powerful and comfortable so that decrease the trafficaccident.
3.We used the imported high quality manganese steel to make the soundboad so that can make the fullest possible "BABA~~" sound.
4.We use the most advanced Teflon coat technology.I can be dust-proof and water-proof effectively(We must inform you that there are not have any horn factory can make a universal horn that all waterproof).It prolong the lifetime of the horn effectively.
5.We used the 100%ABS material to make the horn bulb.It has very good Heat resistance,impact resistance,anti-corrosion so that can prevent the dinas and the heat of the engine damage for the horn.Anyway,it also has high hardness characteristic.It can drop from 1 meter that is not easy to break.

What should I note when I am Installing and using?
a. Snail down or 45 degree Angle installation, Prevent water  into coiled directly
b. If you are not special peason , dont change the angle degree of Steel Support,or it will change the Original air gap
c. mounting torque of Steel support is between 6Nm to 11Nm.
d. The horn support should be mounted to Solid surface to avoid resonance.
e. In order to avoid contact with other parts of the car,The horn should be connected with horn support and installed to wide and Ventilated place.
f. Nonpolarity requirements for this product, the connected place of the wire should solid enough, Double horn should installed on solid part of car body in parallel way.
g. Keep away from car motor and much Radiation place. Not be too low mounting.
h. Don't keep the horn on for 60 seconds, or it will lead to the coil burned down.
i. Using copper wire, more than 1.5mm for wire Diameter, the wire length should less than 4m.
j. Standard mounting Voltage, input working current more than 30A,12V horn voltage: 9-14.5V  


Our company is a professional manufacturer and exporter that is concerned with the design , development and production of auto parts , we are
fully committed to producing technologically advanced auto parts.





Factory show:

Certifications:


Exhibition:


Contact us:
Guangzhou Jindong Electronic Technology Co.,LTD 
Add: No.1,Gudong Industrial Zone,Gulong Road,ShawanTownship,Panyu District,Guangzhou

Summer wei
 
Tel:+86-020-34738085                                  
Mob:+86-13928710276
Fax:+86-020-84737552
 

Y Type Strainer we provided with DIN Y type strainer, API Y type strainer, Ansi Y Type Strainer,High pressure Y type strainer, Pressure seal Y type strainer and Y type rod telescopic strainer are usually installed on the inlet of valve, relief valve or any other decivices to filtering solid particles of the working medium so that making sure all pipeline equipments operation in good condition. Y type strainer we produced can cover size from 1/2"(DN15) to 24"(DN600) matching with pressure class 150(PN16) to class 2500(PN420) which widely used in hot oil system, power station, natuaral gas pipeline, water cycle system etc. The advantages of Y type stariner we provided are easy clean, easy disassembling on line as well as easy maintenance. Strainer screen size can be 20-600 mesh according to the requirements of the customer.

Y type strainer

Y Type Strainer,Y Strainer,Ansi Y Type Strainer,Y Type Industrial Strainer

Yongjia South Trading Co.,Ltd , https://www.n-lvalve.com