WG-9950 Automatic large square cable stripping machine is designed for the large square cable processing research and development equipment, it automatically complete the delivery line, tangent, rotating peeling, peeling. This device solves the difficult problem of processing large square cable in the market, and also changes the traditional parting (end) processing method.
WG-9950 Features: The machine adopts two large belt feeding units, a set of cut-off units, two sets of independent clamping units, two sets of rotary cutting units and two collection of scrap units. From the line into the cut, to the rotary cutting, then to the peeling, the whole computer control. Two sets of independent feeding mechanism using 4 high-power servo motor control respectively feed and discharge, changed the traditional way by the belt clamping cable back and forth of the peeling, such as encountering large adsorption force of the line skin, belt clamping cable in the process of pulling the skin may slip, directly affect the length of the cable precision. When the cable to cut off the edge (can be more than a bit, can also just to the edge of the knife), start the machine, cut off the knife to do the operation, the latter two feed seat to do the opposite direction of movement to the edge, the cable to the rotary cutting edge, clamping line Unit clamping Cable Two rotary knife at the same time rotating cutting both ends, cutting to the set value, micro-retract, after the use of rotary knife wire peel out of the rotary cutter 4 pieces per head, regardless of opening and closing, the middle Cheng Fangkong state, so that in the pull is the cable will not run off Using the screw to move the entire rotating cutting unit to remove the wire skin, so that the length of the cable and the total length of the wire will not be affected, from the increase in the accuracy of the cable length, this process is not like traditional stripping opportunity to waste the front of a cable. After the two clamping lines are clamped, the scrap is sent out along the scrap conveying unit. This way both ends are peeled at the same time, which improves production efficiency Changed the traditional first stripping end, the rear stripping end of the processing method, but also do not waste wire In the rotary cutting unit, the control of the rotary cutter is the use of servo motor with ball screw, rotary peeling is also the use of ball screw peeling, thereby improving the processing accuracy of the large square cable.
Â
Processing line diameter: 10-45mm. (standard) | corresponding processing cable: BV line, BVR hard line DC charging gun cable, AC charging gun cable, high-voltage cable (only peel the skin) electric vehicle battery cable |
processing cable maximum processing length: 20mm (standard) | |
standard cable head end maximum peeling length: 750mm. | Â |
Standard cable end of the maximum stripping length: 1200mm. Semi-stripping | Â |
Feeding method:Belt Feeding | Consumables |
Feeding blade method:Motor + ball Screw | Â |
Machine processing method: Double-ended peeling | Â |
processing rotary blade Material: Powder high-speed steel | consumables |
peeling blade Material: Powder high-speed steel | consumables |
Stripping method: Rotary knife peeling, peel |  |
Operation mode: Touch screen digital operation | Â |
Size: 1900mm long, Width 1300mm, high 1300mm | Â |
Total weight: 650kg (around) | Â |
Power: 5.5 kw (actual operation of 1.8 kw) | Â |
Voltage: AC220V | Â |
 WG-9950 Functional characteristics:
WG-9950 Automatic large square cable stripping machine is designed for the large square cable processing research and development equipment, it automatically complete the delivery line, tangent, rotating peeling, peeling. This device solves the difficult problem of processing large square cable in the market, and also changes the traditional parting (end) processing method.
WG-9950 Features: The machine adopts two large belt feeding units, a set of cut-off units, two sets of independent clamping units, two sets of rotary cutting units and two collection of scrap units. From the line into the cut, to the rotary cutting, then to the peeling, the whole computer control. Two sets of independent feeding mechanism using 4 high-power servo motor control respectively feed and discharge, changed the traditional way by the belt clamping cable back and forth of the peeling, such as encountering large adsorption force of the line skin, belt clamping cable in the process of pulling the skin may slip, directly affect the length of the cable precision. When the cable to cut off the edge (can be more than a bit, can also just to the edge of the knife), start the machine, cut off the knife to do the operation, the latter two feed seat to do the opposite direction of movement to the edge, the cable to the rotary cutting edge, clamping line Unit clamping Cable Two rotary knife at the same time rotating cutting both ends, cutting to the set value, micro-retract, after the use of rotary knife wire peel out of the rotary cutter 4 pieces per head, regardless of opening and closing, the middle Cheng Fangkong state, so that in the pull is the cable will not run off Using the screw to move the entire rotating cutting unit to remove the wire skin, so that the length of the cable and the total length of the wire will not be affected, from the increase in the accuracy of the cable length, this process is not like traditional stripping opportunity to waste the front of a cable. After the two clamping lines are clamped, the scrap is sent out along the scrap conveying unit. This way both ends are peeled at the same time, which improves production efficiency Changed the traditional first stripping end, the rear stripping end of the processing method, but also do not waste wire In the rotary cutting unit, the control of the rotary cutter is the use of servo motor with ball screw, rotary peeling is also the use of ball screw peeling, thereby improving the processing accuracy of the large square cable.
Â
Processing line diameter: 10-45mm. (standard) | corresponding processing cable: BV line, BVR hard line DC charging gun cable, AC charging gun cable, high-voltage cable (only peel the skin) electric vehicle battery cable |
processing cable maximum processing length: 20mm (standard) | |
standard cable head end maximum peeling length: 750mm. | Â |
Standard cable end of the maximum stripping length: 1200mm. Semi-stripping | Â |
Feeding method:Belt Feeding | Consumables |
Feeding blade method:Motor + ball Screw | Â |
Machine processing method: Double-ended peeling | Â |
processing rotary blade Material: Powder high-speed steel | consumables |
peeling blade Material: Powder high-speed steel | consumables |
Stripping method: Rotary knife peeling, peel |  |
Operation mode: Touch screen digital operation | Â |
Size: 1900mm long, Width 1300mm, high 1300mm | Â |
Total weight: 650kg (around) | Â |
Power: 5.5 kw (actual operation of 1.8 kw) | Â |
Voltage: AC220V | Â |
Â
It is a new product suitable for our daily life ,plastic face shield can be used in outdoor activities to prevent damage to s caused by sun or air dust etc.A clear protective film on the surface prevent scratches.
Protective face shield is equipped with a transparent window, which can make the field of vision clearer.
The top of the protective face shields also has a soft sponge and an adjustable elastic band, which is more convenient for users to use. The disposable plastic face shield can be packaged individually or in a pack of 12 according to customer requirements.
The plastic protective film on the plastic surface must be torn off before use.
Product name: Protective Face Shield.
Size: 32*22cm/30*19.5 cm / Customized.
Color: Clear/ Customized.
Material: Double anti-fog PET sheet +sponge + elastic band
Sample: Freely
Sample time: 3-6 working days
MOQ: 216pcs
Application
Quality test
Kids Face Shield,Disposable Plastic Face Shield,Pet Face Shield,Anti-Fog Face Shield
Shenzhen Stardeal Industrial Co.,Ltd , https://www.plasticblisterpacks.com